Star Trek, Greg Jein Copy, 10 Turn Dial Kit, Metal Part, BOURNS PROPORTIONS

Description: In general: all parts are shipped with the machine finish as shown in the LISTING PHOTOS. Final finishing is by the Buyer (prop maker) and may include whatever; polishing, graining, distressing, acid washes, electroplating, and other treatments as selected and executed by the Buyer. Most parts will have some cosmetic blemishes that the Buyer may/may-not want to remove or enhance. Thank You. P2 Engraved 10 Turn Top Dial 3 Part Kit, Boss and Screw design, NEAR EXACT Bourns Dial Replica as seen on the Historic Greg Jein Hero Phaser. Kit Includes: Engraved Dimensional / Proportional reproduction of the 1960s Bourns Dial with machined Clover and No. 4-40 x 3/4 long csk machine screw, This is the easy-to-install version. Easy Install on Star Trek TOS Resin props and similar props where a secure high quality top-turn is needed. Take note the engraved FONTS and TICKS vary ever so slightly from the real Bourns dial, We do offer a 100% accurate Bourns dial but is is a bit more work to install. Dial, Clover, and No. 4-40 csk x 3/4 inch long screw all included. Dimensions are identical to the Historic Greg Jein Hero, thanks to finding some real 1960s Bourns Control Knobs! INSTALLED EXAMPLES FOR REFERENCE PURPOSE ONLY.Hand Machined and quality aluminum, real engraved 10 turn Top Dial, not anodized numbers or ticks,SIZE IN INCHES; 0.735 dia x 0.252 thick overall x 0.109 thru hole for No. 4 screw.Bevel; 0.136 high x 0.191 angular face at 42 degrees and 45 minutes, Undercut; 0.069 diameter x 0.056 high, Real engraving .001" into the surface ! Not acid etched, not printed and, not anodized printed onto the part. Look at the photos, the very fine micro Ra finish produces rainbow effect reflections! * The aluminum is NOT ANODIZED and is of a more workable alloy type than others on the market. Why?, I used a special 6063-T5 (HE-6) un-anodized aluminum because it is workable by a prop builder. Anodizing hardens the material surface and that's not always good because anodizing makes it difficult to work the component. Notably anodizing makes it hard to; machine, grain and/or, further polish, the component. I want you to have options: This component is easy to; mirror polish to brilliance, drill, file, acid weather, rolex grain and, do anything else you can come up with, you're the prop builder and I say have some fun! I also do not like anodizing because it does not look "prop authentic" to the 1960's TV show. Top Turn Clover Details (Item is Included in Kit) * Hand Machined aluminum, polished, 0.491 dia x 0.120 thick x 0.311 octagon hole per photo. Clover fits exactly into the male-boss atop the beveled dial FOR EASY INSTALL, NEED FIBERGLASS SHELLS CLICK AND VISIT: EBAY SELLER "forestlakeip" (https://www.ebay.com/itm/255817798884?hash=item3b8fedd4e4:g:lB0AAOSwL0tiR9x5) MORE FIBERGLASS PHASER SHELLS (https://www.ebay.com/usr/forestlakeip?_trksid=p2047675.m3561.l2559) PASTE LINK TO VIEW; 10-TURN HOW-TO INSTALL AA/DS (https://www.youtube.com/watch?v=1cP8mHfAv6k) LIFETIME WARRANTY AGAINST FAILURE OF ANY KIND INCLUDING DENTING. PASTE LINK TO VIEW; EXPLODED PHASER LSR 12mm SLIDESHOW; YOUTUBE VIDEO (https://www.youtube.com/watch?v=qGj03TyV1dA) PASTE LINK TO VIEW; AA/DS PHASER-LSR 12mm HOW-TO; YOUTUBE VIDEO (https://www.youtube.com/watch?v=e3eY0ImkO7Q&t=1192s)PASTE LINK TO VIEW; TOS-PHASER FIN FINISHING; YOUTUBE VIDEO (https://www.youtube.com/watch?v=AiPjLhyzJzo) PASTE LINK TO VIEW; TOS-PHASER SIDE-RAIL FINISHING; YOUTUBE VIDEO (https://www.youtube.com/watch?v=Mm0_nCrydZo&t=20s) METAL PARTS; Prior to use, all Metal Parts MUST be cleaned to remove machine coolant residue. RESIDUE IS NOT VISIBLE AND DOES NOT FEEL OILY, BUT IT IS THERE! PASTE LINK FOR; EXPLODED PHASER LSR 12mm SLIDESHOW; YOUTUBE VIDEO (https://www.youtube.com/watch?v=qGj03TyV1dA) PASTE LINK FOR; AA/DS PHASER-LSR 12mm HOW-TO; YOUTUBE VIDEO (https://www.youtube.com/watch?v=e3eY0ImkO7Q&t=1192s) PASTE LINK FOR; TOS-PHASER FIN FINISHING; YOUTUBE VIDEO (https://www.youtube.com/watch?v=AiPjLhyzJzo) PASTE LINK FOR; TOS-PHASER SIDE-RAIL FINISHING; YOUTUBE VIDEO (https://www.youtube.com/watch?v=Mm0_nCrydZo&t=20s) METAL PARTS; Prior to use, all Metal Parts MUST be cleaned to remove machine coolant residue. RESIDUE IS NOT VISIBLE AND DOES NOT FEEL OILY, BUT IT IS THERE! Use dish-washing detergent such as "Dawn" or "Palmolive" to insure a clean part. CLICK BELOW FOR: MY YouTube CHANNEL Some Star Trek Prop History For Inquiring Minds: Most of these Prop Makers and Technicians have passed-on. Below are old-timer accounts of convention conversations before conventions were really a fad. (all these are therefore 2nd hand stories) Mr. Bob Stone was Star Trek's machinist and made all the metal prop parts for all three seasons of the show. Parts were made to order for each episode as in those times (the 1960's) as machining was done by hand and there was no advantage to making short runs (and no studio funding either). Each episode had a specific budget. Speaking of budgets, Bob relied on his Star Trek friend Robert Archer (VP of Budgeting for the show) in getting a little leeway on the $ so he could do the best possible job. According to Bob there was no magic drum of Phaser Nozzles and every job was a mad-dash to meet the filming deadlines. Because parts were made only to order, parts varied quite a bit. These variations can be seen in all the surviving examples of TOS hand props from Phaser to Communicators and Tricorders. Sometimes it was not that a new design was needed but rather that when one Wings it from a sketch, in a hurry using what is on-hand, you get an unintended-new-version of something (in the 1960's the TV audience never could see that). Robert Archer and Bob Stone worked closely together so when the show was canceled suddenly in season three, Robert Archer ended up with a nice collection of hand props. Richard Heimer made the molds for hand props. He also did all the casting and forming. This included; Vacuum form bucks, Fiberglass molds and urethane molds. Again, according to him most work is done in the normal Hollywood maddening rush. He shared with his convention friends that there were many molds made from molds when the production schedule demanded this. He also shared that when the show ended he rescued the molds from being discarded by putting them in his garage. James Ruggs (b. 1919) was the director of special effects for the show. He handled and repaired many of the props on-set. When the show was canceled in season three he rescued many hand props and even some models from the scrap heap. Dick Ruben, Prop & Art Assistant on the show, got his Set-Used Klingon disruptor from James. Mr. Ruggs held on to his rather large Star Trek collection for many years. It is widely known that Greg Jein got his Holy-Grail Hero Phaser from James. In closing a nod to Mr. Ruck, a prop technician, who reported that he repaired some hand props hundreds of times as they were often damaged during filming. He had also shared that the fiberglass Mid-Grade's, and some other props often used basswood strips between the seams to establish uniform dimensions. Watch some YouTube Star Trek TOS bloopers to see what he was talking when it comes to repairs and hand props flying apart. NOTICE © and TM 2021. jonpaultrek2012 ® is a registered trademark with the United States Patent and Trademark Office Reg. No.6,431,925 The products sold here are all jonpaultrek2012™® & © 2023 works, are all; custom manufactured & engineered. Jonpaultrek2012 And related marks and logos are trademarks of Jonpaultrek2012 LLC. All Rights are hereby explicitly Reserved. United States Patent & Trademark Office Reg. No. 6,431,925.The jonpaultrek2012 company Supports the right to free expression and the value of the copyright. The purpose of the copyright is to encourage writers, filmmakers and artists to produce the creative works that enrich our culture. All scanning, uploading, and distribution of the content of this web posting without permission is theft of the author's Intellectual Property. if you would like permission to use the material from this website (Other than for the intended review purposes) Please contact me for permission. All new products sold on this website are produced under license From: jonpaultrek2012™® LLC, Florida corporation, located in the United States of America.

Price: 14.41 USD

Location: Brooksville, Florida

End Time: 2024-10-28T01:48:35.000Z

Shipping Cost: 5.99 USD