Professional Car Front Windshield Repair Kit Car Crack Repair Glass Repair Kit

Description: Professional Car Front Windshield Repair Kit Car Crack Repair Glass Repair Kit The hole punch and the curing lamp in this tool set have a voltage of 220v, so these two tools can not be used at 110v. Note: All operations should be carried out indoors or in a dark place to avoid direct or indirect sunlight The glass repair operation is simple, but after getting the tool, you still need to practice more with the waste glass Feature： *Positioning by Support*Easy and fast*High reduction rate*Edge repairProduct parameters:Package weight: 3.5KGPacking size: 30*25*20CM First, crack repairThe permeability of the resin is very strong, only need to apply the resin to the crack, the resin will penetrate into the crack, and then paste the fixed-line diaphragm.Note: 1. In order to let the resin into the crack more smoothly, crack expander can be used to expand the crack. The expander is attached to the inside of the glass, and the top nut in the middle is twisted to expand the crack. Pay attention to the top tightening strength should be moderate, so that the crack can be slightly deformed, too much force will make the crack continue to grow.2. Crack repair should start from the lowest level of the horizontal position, and observe the resin entry at a 45 degree Angle with the glass. If the length of the crack exceeds 10cm, it is necessary to repair the curing film on the edge, and use the purple lamp to fix the whole crack once it is filled with resin.Second, the repair methods of the three symptoms of bull's eye, star type and comprehensive type crack repair are consistent. There will be an obvious impact point in the middle of the bull's eye and comprehensive cracks. If the impact point of the star crack is not found, a glass punch can be used to make an impact point at the Citic position (the impact point is used as the resin entry point during the repair process). The perforator holes vertically and penetrates one layer of the surface of the double laminated glass.Repair process:1. Use a brush and steel needle to clean debris at the impact point2. Install a three-jaw repair support. Adjust the position of the support so that the center hole of the support is aligned with the impact point of the glass.3. Install the repair solution so that the sealing gasket at the liquid injection mouth is close to the glass. Observe that the round hole of the sealing gasket is in line with the impact point, and tighten the lock nut.4. Extract a certain amount of resin (generally 0.2ml) into the injection nozzle5. Install the fixer and tighten it6. Vacuum, pull the repair rod up, and then rotate 90 degrees to fix it. The vacuum time is 3-5 minutes, and the bubbles at the injection nozzle are observed7. Pressure operation: loosen the air valve, and tighten the air valve after the gas enters the repair cylinder. Pull the tie rod back down and tighten the tie rod lock nut. Pressure operation time 3-5 minutes.8. Observe the crack change, accompanied by vacuum, pressure operation cracks gradually become smaller until disappeared. (If there is still air after a pressurization operation, repeat the vacuum and pressurization operation.) Proceed to the next step.9. Tighten the air valve and remove the support10. Paste cured film: paste cured film on the crack surface, and add a drop of resin at the impact point to ensure that the surface repair liquid at the impact point is full11. Fixed violet lamp curing 3-5 minutes12. Tear off the curing film and remove excess resin with the blade. Operation complete NOTE: 1.lmport duties, taxes and charges are not included in the item price and the freight. These charges are the buyer's responsibility. 2.Please check with your country's customs to determine what these additional costs will be prior to bidding/buying. 3.Please leave your valid phone number when you make order, otherwise we can't guarantee the package would arrive smoothly. RETURN 1.Return accepted in 30 days after you receive the item. The buyer need to affordthe return postage fee who also need to return it to our designated place. 2.Return package must be in the original packaging, item must be in new condition.Missing parts or any damaged by the buyer will not give any return. 3.Within warranty period, all repair parts will be free, but the buyer need to pay for the freight.

Price: 143.88 USD

Location: 郑州市

End Time: 2024-08-02T02:44:45.000Z

Shipping Cost: 14 USD