Morningstar SK-6 SunKeeper 6 amp 12 volt Solar Charge Controller

Description: Morningstar SK-6 SunKeeper 6 amp 12 volt Solar Charge Controller Morningstar Sunkeeper SK-6 Junction Box Mounted Solar Controller Morningstar’s SunKeeper solar controller provides a low cost regulated output directly from the solar module to maximize battery life in small solar power applications. The SunKeeper is epoxy encapsulated and rated for outdoor use. By mounting directly to the module junction box and wiring through the junction box knockout, the connection is weather-proof. This eliminates the need for an additional housing for the controller. Key Features and Benefits: High Reliability - Rated to 70°C to operate in high temperatures at the solar module. More reliable than controllers mounted inside the junction box. Uses very low on-resistance power MOSFET’s. No need to re-rate.Outdoor Rated - ETL approved for outdoor use without an additional enclosure. Rugged IP65, UV resistant case. Epoxy encapsulated printed circuit board and watertight connection to the module junction box.Extensive Electronic Protections - Fully protected against reverse polarity, short circuit, overcurrent, lightning and transient surges, high temperature and reverse current at night.Longer Battery Life - Series PWM with 3 stage charging: bulk, PWM regulation and float. Includes temperature compensation at the controller or alternatively at the battery when using optional remote temperature sensor. Able to charge a zero voltage battery.Rated for Hazardous Locations - Specifically designed for solar power systems in the oil/gas industry. Approved for use in Class 1, Division 2, Groups A,B,C,D.More Information - Bi-color LED is easy to read from the ground when the solar module is pole-mounted. Indicates solar charging, regulation, normal nighttime operation and any controller or system faults.Easy to Install - Fits standard half inch conduit knockout (PG 13.5, M20) in module junction box. Quickly fastens with included locknut. Wires have fork connectors for easy connection to solar module terminals. Technical Specifications: Rated Solar Input SK-6: 6 amps Nominal System Voltage 12 Volts Minimum Battery Voltage 0 Volts Maximum Solar Voltage 30 Volts Self-Consumption (Charging) 7 mA Self-Consumption (Night) 2 mA Battery Charging Regulation Voltage 14.1 Volts (at 25°C) Float Voltage 13.7 Volts (at 25°C) Type of Charging Series PWM - 3 Stage: bulk, PWM and float Operating Temperature - 40°C to + 70°C Dimensions 3.9" x 2.0" x 0.5" (99mm x 51mm x 13mm) Weight 0.25 lbs (0.11 kg) Fitting to Module J-box PG 13.5, M20, 1/2 inch conduit Wire Size #14 AWG (2.0 mm2) Wire Terminations #8 fork connectors Hurricane Wind Power 2019Corporate America Today2019 Best Off-Grid Renewable Energy Product Supplier - USAUP TO 50% DISCOUNTSTOP BRANDSPaymentShippingReturnsPaymentShippingReturns We accept payment by any of the following methods: PayPal Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner! We offer Fast shipping on all orders! Your order will be dispatched within 1-3 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class). In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement. If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not. You can return a product for up to 14 days from the date you purchased it. Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt. See our other itemsThank you for visiting our Ebay store!Morningstar Sunkeeper SK-6 Junction Box Mounted Solar Controller Morningstar’s SunKeeper solar controller provides a low cost regulated output directly from the solar module to maximize battery life in small solar power applications. The SunKeeper is epoxy encapsulated and rated for outdoor use. By mounting directly to the module junction box and wiring through the junction box knockout, the connection is weather-proof. This eliminates the need for an additional housing for the controller. Key Features and Benefits: --- High Reliability - Rated to 70°C to operate in high temperatures at the solar module. More reliable than controllers mounted inside the junction box. Uses very low on-resistance power MOSFET’s. No need to re-rate. ---Outdoor Rated - ETL approved for outdoor use without an additional enclosure. Rugged IP65, UV resistant case. Epoxy encapsulated printed circuit board and watertight connection to the module junction box. ---Extensive Electronic Protections - Fully protected against reverse polarity, short circuit, overcurrent, lightning and transient surges, high temperature and reverse current at night. ---Longer Battery Life - Series PWM with 3 stage charging: bulk, PWM regulation and float. Includes temperature compensation at the controller or alternatively at the battery when using optional remote temperature sensor. Able to charge a zero voltage battery. ---Rated for Hazardous Locations - Specifically designed for solar power systems in the oil/gas industry. Approved for use in Class 1, Division 2, Groups A,B,C,D. ---More Information - Bi-color LED is easy to read from the ground when the solar module is pole-mounted. Indicates solar charging, regulation, normal nighttime operation and any controller or system faults. ---Easy to Install - Fits standard half inch conduit knockout (PG 13.5, M20) in module junction box. Quickly fastens with included locknut. Wires have fork connectors for easy connection to solar module terminals. Technical Specifications: Rated Solar Input SK-6: 6 amps Nominal System Voltage 12 Volts Minimum Battery Voltage 0 Volts Maximum Solar Voltage 30 Volts Self-Consumption (Charging) 7 mA Self-Consumption (Night) 2 mA Battery Charging Regulation Voltage 14.1 Volts (at 25°C) Float Voltage 13.7 Volts (at 25°C) Type of Charging Series PWM - 3 Stage: bulk, PWM and float Operating Temperature - 40°C to + 70°C Dimensions 3.9" x 2.0" x 0.5" (99mm x 51mm x 13mm) Weight 0.25 lbs (0.11 kg) Fitting to Module J-box PG 13.5, M20, 1/2 inch conduit Wire Size #14 AWG (2.0 mm2) Wire Terminations #8 fork connectors [FREE! Sellers: Add a FREE map to your listings. FREE!] (http://newage.mystoremaps.com/echo/tagLine?sid=cea073c8-fc6f-494f-9ca5-610e8850a127&tid=2) Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application Morningstar SK-6 SunKeeper 6 amp 12 volt Solar Charge Controller Morningstar Sunkeeper SK-6 Junction Box Mounted Solar Controller Morningstar’s SunKeeper solar controller provides a low cost regulated output directly from the solar module to maximize battery life in small solar power applications. The SunKeeper is epoxy encapsulated and rated for outdoor use. By mounting directly to the module junction box and wiring through the junction box knockout, the connection is weather-proof. This eliminates the need for an additional housing for the controller. Key Features and Benefits: High Reliability - Rated to 70°C to operate in high temperatures at the solar module. More reliable than controllers mounted inside the junction box. Uses very low on-resistance power MOSFET’s. No need to re-rate.Outdoor Rated - ETL approved for outdoor use without an additional enclosure. Rugged IP65, UV resistant case. Epoxy encapsulated printed circuit board and watertight connection to the module junction box.Extensive Electronic Protections - Fully protected against reverse polarity, short circuit, overcurrent, lightning and transient surges, high temperature and reverse current at night.Longer Battery Life - Series PWM with 3 stage charging: bulk, PWM regulation and float. Includes temperature compensation at the controller or alternatively at the battery when using optional remote temperature sensor. Able to charge a zero voltage battery.Rated for Hazardous Locations - Specifically designed for solar power systems in the oil/gas industry. Approved for use in Class 1, Division 2, Groups A,B,C,D.More Information - Bi-color LED is easy to read from the ground when the solar module is pole-mounted. Indicates solar charging, regulation, normal nighttime operation and any controller or system faults.Easy to Install - Fits standard half inch conduit knockout (PG 13.5, M20) in module junction box. Quickly fastens with included locknut. Wires have fork connectors for easy connection to solar module terminals. Technical Specifications: Rated Solar Input SK-6: 6 amps Nominal System Voltage 12 Volts Minimum Battery Voltage 0 Volts Maximum Solar Voltage 30 Volts Self-Consumption (Charging) 7 mA Self-Consumption (Night) 2 mA Battery Charging Regulation Voltage 14.1 Volts (at 25°C) Float Voltage 13.7 Volts (at 25°C) Type of Charging Series PWM - 3 Stage: bulk, PWM and float Operating Temperature - 40°C to + 70°C Dimensions 3.9" x 2.0" x 0.5" (99mm x 51mm x 13mm) Weight 0.25 lbs (0.11 kg) Fitting to Module J-box PG 13.5, M20, 1/2 inch conduit Wire Size #14 AWG (2.0 mm2) Wire Terminations #8 fork connectors FREE! Sellers: Add a FREE map to your listings. FREE! Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application Hurricane Wind Power 2019Corporate America Today2019 Best Off-Grid Renewable Energy Product Supplier - USAUP TO 50% DISCOUNTSTOP BRANDSSee our other itemsPayment We accept payment by any of the following methods: PayPal Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner! Shipping We offer Fast shipping on all orders! Your order will be dispatched within 1-3 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class). In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement.Returns If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not. You can return a product for up to 14 days from the date you purchased it. Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt. Thank you for visiting our Ebay store! Morningstar Sunkeeper SK-6 Junction Box Mounted Solar Controller Morningstar’s SunKeeper solar controller provides a low cost regulated output directly from the solar module to maximize battery life in small solar power applications. The SunKeeper is epoxy encapsulated and rated for outdoor use. By mounting directly to the module junction box and wiring through the junction box knockout, the connection is weather-proof. This eliminates the need for an additional housing for the controller. Key Features and Benefits: High Reliability - Rated to 70°C to operate in high temperatures at the solar module. More reliable than controllers mounted inside the junction box. Uses very low on-resistance power MOSFET’s. No need to re-rate.Outdoor Rated - ETL approved for outdoor use without an additional enclosure. Rugged IP65, UV resistant case. Epoxy encapsulated printed circuit board and watertight connection to the module junction box.Extensive Electronic Protections - Fully protected against reverse polarity, short circuit, overcurrent, lightning and transient surges, high temperature and reverse current at night.Longer Battery Life - Series PWM with 3 stage charging: bulk, PWM regulation and float. Includes temperature compensation at the controller or alternatively at the battery when using optional remote temperature sensor. Able to charge a zero voltage battery.Rated for Hazardous Locations - Specifically designed for solar power systems in the oil/gas industry. Approved for use in Class 1, Division 2, Groups A,B,C,D.More Information - Bi-color LED is easy to read from the ground when the solar module is pole-mounted. Indicates solar charging, regulation, normal nighttime operation and any controller or system faults.Easy to Install - Fits standard half inch conduit knockout (PG 13.5, M20) in module junction box. Quickly fastens with included locknut. Wires have fork connectors for easy connection to solar module terminals. Technical Specifications: Rated Solar Input SK-6: 6 amps Nominal System Voltage 12 Volts Minimum Battery Voltage 0 Volts Maximum Solar Voltage 30 Volts Self-Consumption (Charging) 7 mA Self-Consumption (Night) 2 mA Battery Charging Regulation Voltage 14.1 Volts (at 25°C) Float Voltage 13.7 Volts (at 25°C) Type of Charging Series PWM - 3 Stage: bulk, PWM and float Operating Temperature - 40°C to + 70°C Dimensions 3.9" x 2.0" x 0.5" (99mm x 51mm x 13mm) Weight 0.25 lbs (0.11 kg) Fitting to Module J-box PG 13.5, M20, 1/2 inch conduit Wire Size #14 AWG (2.0 mm2) Wire Terminations #8 fork connectors FREE! Sellers: Add a FREE map to your listings. FREE! Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application

Price: 68 USD

Location: Roanoke, Virginia

End Time: 2024-08-03T19:55:03.000Z

Shipping Cost: N/A USD