LUXURY LINER MASS LOADED MLV VINYL SOUNDPROOFING SHEETS 2 LB Per SqFt

Description: Road noise, engine, and exhaust noise are a big component of most automotive noise problems. Second Skin Luxury Liner is a barium infused mass loaded vinyl, designed to block even the most stubborn airborne sound waves. Luxury Liner works best as the final layer in a multi-layer vehicle sound insulation project. Start with a sound deadener (Second Skin Audio's Damplifier Pro or Spectrum) for the metal structure noise. Then add a decoupling layer (Heat Wave Pro or OverKill Pro) to decouple and add thermal insulation, and then finally use Luxury Liner as your sound barrier Luxury Liner is a black mass loaded vinyl we make right here in the USA. This is not a cheap, recycled MLV. It's flexible and pliable with over 3x the tensile strength of lower quality versions (600 psi). Luxury Liner is odorless and fire resistant, passing vehicle safety testing standards (FMVSS 302). MLV SOUND BARRIER: Luxury Liner 2 lb per sq ft is a 1/4 inch thick, mass loaded vinyl noise barrier designed to stop road, exhaust, and engine noise. This dense MLV acoustic barrier is 2 lb per sq foot and used in cars, trucks, Jeeps, and SUVs.DURABLE THERMAL INSULATION: Luxury Liner Pro is odorless, flexible, and heat resistant up to 180 F. Its high R-value (4.45 per inch) makes it an excellent heat insulation mat. Combine MLV with a sound deadener (like Damplifier Pro) to 2x results and get the best combination of heat and sound insulation money can buy.PROTECT YOUR VEHICLE: The goal is a 100% unbroken barrier covering the car’s firewall (cabin side), floor, and trunk. Each sheet is 9 Sq Ft (2 ft by 4.5 ft) so several may be needed for 100% coverage – measure your car. Apply a strong vinyl adhesive to the top of the sound deadening product and the vinyl of the Luxury Liner . Do not hang this product roof or hood.PROUDLY MADE IN THE USA and endorsed by Chad Utt of WEST COAST CUSTOMS 1/4" thick, raw virgin mass loaded vinylEach sheet is 24" x 54" (9 Sq Ft)Weight: 18 pounds per sheetSTC rating: 32 (about a wall in your house)Best for: targeted automotive (diesel noise, exhaust noise), soundproof box, walls, ceilings, floors, and other flat surfacesMade in the USAProduct UsageSecond Skin's Luxury Liner MLV should be used in combination with a decoupling product for best results in vehicles. We recommend OverKill Pro (closed cell foam) or Heat Wave Pro (jute and foil blanket). This MLV noise barrier is cut into sheets that are a great size for generator boxes and other small soundproofing projects. Cut with a sharp utility knife or a good pair of upholstery scissorsNormal adhesives will not work on vinyl. You need a specific product such as our HH-66 Vinyl Adhesive, Dual Lock Reclosable Fasteners, or to fasten it with nails, screws, or staples.If you're looking for a full roll, we have several options to buy mass loaded vinyl. We recommend full rolls for residential applications inside the walls, floors, or ceiling. Recommended Install LocationsFloor - front firewall all the way back to the rear deck seat wallFirewall - cabin sideTrunk - entire floor including over the wheel wellsApplication InstructionsFor best results, Luxury Liner should be applied on top of a sound deadener, such as Second Skin Audio's Damplifier Pro or Spectrum. It’ll be the final layer of your multi-layer sound insulation bubble.Choose your decoupler. For the floor of vehicles, we typically recommend OverKill Pro (closed cell foam) or Heat Wave Pro (jute material). OverKill Pro will create an overall better barrier layer, whereas the Heat Wave Pro is a better thermal insulator and sound absorber. You can't go wrong with either product.If upholstery or carpet is not already out, remove it. Ensure there’s no loose debris, rust, dirt, or waxy oils.Cut Luxury Liner to the desired size with a sharp utility knife or a good pair of scissors. Be sure to cut to a size that will allow you to reinstall the carpet and upholstery trim. Do not cover wires, drain holes, or mechanical devices. This part of the project is more art than science, as you need to have as few gaps as possible in your noise barrier while avoiding interference with other parts of the car.Use vinyl cement, such as HH-66 Vinyl Adhesive to adhere the Luxury Liner to the decoupler of choice. Apply one coat on the Luxury Liner Vinyl and one to the decoupling product.Apply a second adhesive to the decoupler and the foil side of your Damplifier Pro. You can reuse the contact cement or use ahigh temp spray adhesive or double sided tape. If using a spray adhesive, wait 1-2 minutes for the gases to be released from the glue and it to become tacky. Then press the tacky side of the decoupler down to the foil side of your sound deadener. Apply constant pressure over the entire surface for several minutes to ensure a solid bond.Seal any exposed edges or seams with Foil Tape. The goal is to create as close to an unbroken noise barrier as possible.Factory carpet can be replaced immediately. Aftermarket carpet kits can be attached directly to the exposed mass loaded vinyl side of Luxury Liner. Sound Transmission Loss Frequency (Hz) 125 250 500 1000 2000 4000 Sound Transmission Loss (dB) 15 19 24 32 36 42 STC Rating: 32

Price: 74.99 USD

Location: Libertyville, Illinois

End Time: 2023-12-25T21:43:54.000Z

Shipping Cost: N/A USD