Heavy Duty Pan Seal Kit Model CBK-100 (7MKIT-HD) for Cuisinart Bread Maker

Description: Brass Check Valve G1" 64x41mm Male Female Thread Non-Return Backflow Prevention18.79 USDFree shippingAM133408 BM23765 Power Lift Actuator For John Deere Utility Gator 6X4 4X2 TX TH269.79 USDFree shippingTransparent Outdoor Disco DJ Waterproof LED Stage Lighting Par Rain Cover UE22.79 USDFree shipping5pc Normally Closed Momentary Self-resetting Push Button Reset Switch w/Wire Red20.79 USDFree shipping12V 24V Max 20A PWM DC Motor Stepless Variable Speed Control Controller15.79 USDFree shipping12V to 19V 10A 190W DC-DC Boost Step Up Power Converter Voltage Regulator Module26.79 USDFree shipping Heavy Duty Pan Seal Kit Model CBK-100 (7MKIT-HD) for Cuisinart Bread Maker Product Description (Includes: Heavy Duty Seal, Stainless Flat Washer, Stainless Steel Snap Ring & Stainless Steel E-clip)*You will need Snap Ring Pliers to properly remove & install the snap ring.will fit the models listed below:Cuisinart BreadmakerAutomatic Dough & Bread Maker MachineModel Number: CBK-100THANK YOU!Bread Machine Parts Finder***Important message about replacing the red seal in the pan: *(If you do not see a visible red seal inside the pan, then please do not attempt to install this seal kit.)*(Only fits pans that have the visible red pan seal from top side.)*(You will need Snap Ring Pliers to remove and install the Snap Rings.)*(You may need an E-clip installation tool to install the E-clip.)***Warning! Before you attempt to install a new seal, you should always check for thin cracks around the rivet heads on the inside bottom of the pan. If you find a crack in the pan, then you will know the pan is leaking through that crack and is not repairable. If a rivet has loosened, appears to be coming out, or you can move the rivet head with your fingertip, then the pan will leak through that point. A new seal will not solve that problem. If you do not find any cracks or loose rivets, then continue reading and following through with the repair.Most of the older red seals issued with the pans were manufactured with an outer diameter of 19mm. The 19mm outer diameter seal was cut down to 17mm by the manufacturer of the pan to make it fit into the 17mm diameter hole of the pan. If your pan has this old seal and the pan shaft is still secure, then you may push the seal out by removing the Snap Ring & Wing Nut Impeller from the bottom of the shaft. Then with minimal force push the shaft up and out the top of the pan. This action will push out the seal. If the shaft will not push through without using excessive force that may damage the pan, then please follow the directions in paragraph 2 & 3. If the pan shaft has already come loose and fell out the bottom of the pan, then you will need to follow the directions below in paragraph 2 & 3. The newer red seals in later productions of the pans are custom made two tear seals that have a bottom outer diameter of 19mm and an upper outer diameter of 17mm. These seals must be removed by prying them out with a double ended bottle/can opener or a pick & hook set. The seal can only be pried out if the pan shaft has fallen out the bottom of the pan. If the pan shaft is still secure, then you will not be able to get the seal out without damaging the pan. In this case please do not order a new seal. Please order a new pan.***If the shaft has already fallen out the bottom, then you will need to pry out the old seal using an old double ended can opener / bottle opener. Place a business card or credit card in the bottom of the pan to prevent scratching when using the can opener to pry out the old seal. Place the pointed end of the opener into the center hole of the seal and gently pry upward moving from side to side until the seal pops out. Please note that the seal has an inner steel frame. If all you have removed so far is a thin piece of rubber, then you will need to remove the rest of the seal known as the inner frame. It is important that you be very careful when removing the old seal. If the hole the seal is in becomes swelled, warped, or chipped then the new seal may not seat successfully. ***I strongly recommend removing the old seal before purchasing a new seal so that you can determine if the pan is in fact repairable. Please remove the seal first and use a magnifying glass to inspect the hole for chipped off non-stick coating, pitting, corrosion, dings, dents, swelling, or warping. If any of the damage above is present, then please do not order a seal. I can guarantee that it will not seat or seal correctly.***Please be aware that each time you replace the seal it may not last as long as the previous seal, because the sleeve bearing in the bottom of the pan continues to wear, which causes more wobble that creates more stress for the seal to bear. The thin washer included in the seal kit replaces the Nylon, Teflon, or Fiber washer that was placed under the E-clip on the drive shaft. You will re-use any metal washers found on the bottom end between the sleeve bearing and the wing nut impeller. About Us Shipping Terms Contact Us Payment About Us Founded in 2012, VIPJQ have professional development and sales, and are involved in various products, providing customers with various high-quality products. Since its establishment, VIPJQ has always adhered to the service concept of "customer first" and the management concept of "pursuit of quality", and is committed to providing customers with high-quality original designs. We commit to provide you the best innovative, quality products & professional services with competitive prices. We value every customer, and we look forward to providing solutions for your business needs to help your business achieve its goals, please contact us immediately! We are all about you! Shipping US BuyersParcel will ship via USPS/DHL/FedEx from our United States warehouseShipping timeThe item usually will be dispatched within 3 days after you ordered.And it usually takes 3-10 working days to delivery depends on buyers address or other majeure on the way. ServiceWe stand behind everything that we sell and will do everything possible to assure you are satisfied Terms When you receive your purchase if you are not 100% satisfied, please sent me ebay message and we will do our best to meet your expectations. If you still want to return your purchase, simply ship the item(s) back to us and we will refund your original purchase price and the original shipping charge. We must be notified of the intent to return your item within 30 days of receiving the item.How to return1. Please ask us for return address .2. Shipping back the package . 3. Send us the return tracking number. 4. Refund full to you when we receive the package.5. Please leave positive feedback and 5-star rating, it helps us do better for you. Contact Us We can be contacted at any time through eBay messages if you have any questions, comments or product requests. We will respond to you within 24 hours and do our best to help you out!Please give us a chance to resolve the issue before leaving us a feedback. Payment 1. We Accept Visa, Master, Amex, Google Pay，Discover, Paypal, etc, many payment ways.2. Item will be shipped immediately on the same or next business day of receiving your payment. Copyright © 2022 Tongtool

Price: 18.79 USD

Location: Los Angeles, California

End Time: 2024-11-08T18:27:56.000Z

Shipping Cost: 0 USD