Electrostatic Coating System Manual Powder Spraying Machine Paint Gun Potable

Description: eBay Introduction: 1.It is an ideal spray tool for spraying various metal parts to make the workpiece beautiful and durable. It can be sprayed for any metal parts. The sprayed surface after forming can prevent corrosion of a variety of chemical substances and ultraviolet radiation. It is much stronger than liquid spray and more than ten times stronger than ordinary paint. In the production process, there is no need to add any organic solvents, no toxic volatiles are produced, and no environmental pollution is caused. 2.No special training is required to use this product. As long as you read the manual carefully, you can fully master it in a short period of time and operate it proficiently to realize your ideas and obtain the ideal decorative parts with plastic spraying. 3.This product is an ideal spray tool for you to spray various metal parts on the surface to make the workpiece beautiful and durable. It can be sprayed for any metal parts. The sprayed surface after forming can prevent corrosion of a variety of chemical substances and ultraviolet radiation. It is much stronger than liquid spray and more than ten times stronger than ordinary paint. In the production process, there is no need to add any organic solvents, no toxic volatiles are produced, and no environmental pollution is caused. Features： 1.Power Coating System provides a premium coating ideal for many automotive, marine, home and garden applications. 2.The Powder Coating System is a breakthrough refinishing system for the home hobbyist providing professional performance at a fraction of the cost of professional equipment. 3. It produces a finish that is resistant to most chemicals, fuels, acids, thinners, brake fluid, UV light, and is much more durable than liquid coatings(up to ten times more durable than ordinary paint). 4. Powder coating is environmentally friendly! It produces no toxic wastes and uses no solvents. 5. With the Powder, blow it off with compressed air and recoat. Cured powder coating can be recoated with powder and baked or touched up with paint. 6, You can operate it without special training Specification: Power requirements: Use a 220V AC power supply with safety grounding. When in use, the machine must be grounded. Air source requirements: The compressed air pressure used must be 0.5 to 1.2 kg. It is recommended to use 1.0 kg, when the air pressure is the most ideal. Environmental requirements: well ventilated and dry. Gross/net weight: 3/ 2.5kg Power volatge: 110VAC 60Hz, 240VAC 50Hz AMPS: 0.03A Voltage output: 25KV+/-5KV Require Air supply: 10-15 PSI, Dry air 5CFM WATTS: 3.3W Power Cord: 16AWG Air Inlet: 1/4” NPT Thread This machine adopts the integrated circuit board. Preparation before use: 1. Preparation of sprayed parts: the surface of the sprayed parts should be rust-removed, degreasing, and phosphated. The parts should have a dry, smooth and clean surface. 2. Prepare an oven so that the sprayed parts can be put into the oven for baking. The sprayed parts are best hung in the oven with metal spreaders. 3. Prepare a power supply and socket with the same voltage as the injection molding machine. The power supply must have a safety ground. 4. Prepare the gas source. The air source pressure is generally 0.5 kg to 1.2 kg, and 1.0 kg air source pressure is recommended. 5. Put the dry plastic powder into the bottle, and the amount of plastic powder is about 5 cm from the bottom of the bottle. Caution: 1.Because this machine generates high-voltage static electricity, the user's work place and equipment must be dry when using it. In addition, the machine must be safely grounded. Do not unplug the grounding plug. This is important for protecting the machine and preventing electric shock. To avoid danger, after each use, the discharge needle must be touched to the ground clamp to discharge. 2.When the particles of plastic powder fall into the air, they will encounter a fire source, and there is a danger of burning and explosion. Therefore, all hidden dangers must be eliminated and all fire sources must be isolated. Do not use a vacuum cleaner to remove the plastic powder on the ground. Wear a dust cover when working to protect personal safety.

Price: 340.88 AUD

Location: shenzhen

End Time: 2024-11-09T09:28:54.000Z

Shipping Cost: 0 AUD