AUTOPAGE XT-75 antennae KEYLESS REMOTE CAR STARTER key FOB ALARM H50T16 H5OT16

Description: Stock #: 693cOne (1) Pre-Owned Aftermarket remote keyless entry fob alarm Transmitter control clicker keyfob controller replacement FUNCTIONS AT 100% TESTED & GUARANTEED Megatronix / Autopage FCC ID: H50T16 H5OT1 Part # MODEL: XT-75 XT75 Frequency: 433.92 MHz LED color: red 4 buttonsBattery: 2; CR2025 Replacement: AUTOPAGE Programming Instructions:Transmitter Programming MANUAL Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is exceeded, the security system will start deleting transmitters from memory in chronological order. 1. Turn the Ignition 'switch ‘OFF/ON’ 3 TIMES and stay in ON position. “Within 15 seconds”. 2. Push the Valet switch 2 times and hold it on the 2nd push until a long chirp is heard then release the valet switch. You are now in the Transmitter programming mode. 3. Press and hold any button of the transmitter until the siren responds with a confirming chirp, indicating the signal has been stored into memory. 4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for each transmitter. Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit. 8 PIN CONNECTOR WIRE HARNESS: ALARM FEATURE “B” PROGRAMMING: Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. Push the Valet switch 5 times and hold in on the 5th push. When a long chirp is heard, release the valet switch. You are now in the Alarm feature ‘B’ programming mode. Press the transmitter button corresponding to the feature you want to program. One Chirp / LED Press one pulse Four Chirps / Transmitter Two Chirps / LED Three Chirps / LED LED four two pulses three pulses pulses Factory Default Button Setting Pathway Parking light turns Parking light turns illumination feature “on” for 30- second “on” for 30- second “off” upon an unlock upon an unlock signal signal & 10-second upon a lock signal. Ignition controlled Without ignition Ignition controlled Ignition controlled door locks & controlled door door locks only door unlocks only unlocks locks & unlocks * Starter Kill relay optional ALARM FEATURE “I” PROGRAMMING: Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. Push the Valet switch 3 times and hold in on the 3rd push. When a long chirp is heard, release the valet switch. You are now in the Alarm feature ‘I’ programming mode. Press the transmitter button corresponding to the feature you want to program. a. The factory default settings is always [1] LED flash, [1] chirp. Depress the transmitter button again to change the feature. Simply keep pressing the transmitter button again until the module advances to your desired setting. Press Transmitter Button One Chirp / LED one pulse Factory Default Setting Active arming 5 PIN WIRE HARNESS 1. Red / White Wire: Parking Light Relay input 4. Brown Wire: Positive output To Siren 5. Red Wire: +12V To Constant Battery Source Passive arming without passive door locking Automatic Rearm on Instant Door Ajar error chirp 45 seconds delay Door Ajar error chirp. Siren Confirmation chirp on only All Confirmation chirps On 15A Fuse White wire= Dome Light Output This manual was written September 1, 2015 7. ©2015 Varad International, Inc. All rights reserved. 8. GI-S346 LED two pulses Automatic Rearm off 2. White Wire: Parking Light Relay Output 3. Black Wire: Ground to Vehicle FRAME Two Chirps / White wire= 4th Channel Momentary Lock/Arm & Unlock/Disarm Confirmation Chirps Lock/Arm Confirmation Chirp Only ALARM with Keyless Entry Keyless Entry ONLY Car Jacking feature Off Car Jacking feature On Three Chirps LED three pulses Passive arming with passive door locking. 0.8-second Door lock pulses. 3rd Channel Pulsed Four Chirps / LED four pulses 7. 3.5-second Door lock pulse. Double pulse unlock Comfort feature 3rd Channel Momentary Button = 4th Channel Aux. Button = Silent Arm/Disarm Gray Wire = Trunk (Channel 3) Output Gray Wire = Two Step Door Unlock Output Horn chirp Duration Horn chirp Duration Horn chirp Duration Standard 50 mS 30 mS Horn chirp duration 10 mS Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm exit. SHOCK SENSOR ADJUSTMENT Horn Confirmation chirp on only White = 4th channel Latched All Confirmation chirps off 1. 2. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position. Push the Valet switch 7 times holding in on the 7th push. Three chirps with a long chirp will be heard. Release the valet switch. You are now in the Alarm feature ‘Shock Sensor’ programming mode. 3. Press and hold shock sensor. 4. Press button on the transmitter once. This will decrease sensitivity level by one. Each time the button is pushed and a decrease is made the siren/horn chirp will respond with [1] chirp. Two chirps indicate the minimum sensitivity. Warn away & full trigger will be deleted when minimum sensitivity is selected button for 2 seconds. One long siren chirp will indicate the unit is ready to accept adjustments of the 5. Press button on the transmitter once. This will increase sensitivity level by one. Each time an increase is made the siren/horn chirp will respond with [1] chirp. Two chirps indicate the maximum sensitivity. 6. Hit the bumper or strong metal part of the vehicle to test the threshold level of the sensor. a). Activate the warn-away (first stage the shock sensor), the siren will emit a short chirp. b). Activate the full alarm (second stage the shock sensor), the siren will emit a long chirp. 7. When you are satisfied with the setting, press the unit has locked in the adjustment. button to lock in the adjustment. One long siren chirp will indicate the Note: If 30 seconds of inactivity expires or you turn ON the ignition during of above steps, the unit will exit the program mode and return to the disarmed mode. Three long chirps will confirm exit. 100% Guarantee Remote Shipping / Return Policy Warranty/Returns: 1. We have a 30 day return policy. 2. All returns for replacements and refund need an RMA #. 3. Please contact us before returning items so we can give you the RMA # and the proper return address. 4. No refunds / replacements will be granted without an RMA# We ensure proper working condition of all previously used or new remotes through a serious of tests performed with the Santronics Testing device. Each button is tested for functionality prior to shipment and then logged. Please Note: Each remote and circuit board is UV id’d prior to shipment – All returns receive a UV ID inspection to verify originality of remote sent prior to refund or replacement. Does this keyless remote entry come with a battery? Yes. It will have a working battery installed. Battery Condition: A. All remotes sold on Keyless4u include working batteries. B. Installed batteries are not tested for battery life- they are simply working. Some are new and some are used. Your vehicle will be installed with one of the following keyless entry systems: a. Standard Keyless Remote Packages: Installed at time of manufacture. b. Optional Keyless Remote Packages: Installed by a dealer. c. Aftermarket Keyless Remote Packages: Installed by previous owner or a car/audio shop. d. No remote keyless entry system at all. The above information can change which remote you need for your installed remote keyless system.

Price: 71.59 USD

Location: Wellsboro, Pennsylvania

End Time: 2024-12-26T21:14:57.000Z

Shipping Cost: 6.96 USD