1992-98 GMC SUBURBAN YUKON 1500 2500 3500 SIERRA GMC FRONT EMBLEM BLACK

Description: This emblem replace the RED and chrome factory bowtie emblem in the front. MADE IN THE USA WARRANTY IS FOR 90 DAYS FROM DATE OF PURCHASE We offer(Price is for only 1 emblem Front only in Black THIS EMBLEM IS made of high quality billet aluminum CNC machined Fits: 1988-1998- 1500 2500 3500 SIERRA 1992-1998 - Yukon 1992-1998- Suburban Your order will ship within 2 business 95% of the time(business days are only Monday through Friday), but most of the time it will leave within hours of making your payment. So make sure when checking out you double check your address BEFORE you buy as it may be to late to change it. Also tracking numbers are posted on ebay under the transaction and are e-mailed to your e-mail address you have listed on the paypal payment page. Also if you can't leave us top marks in every category we would like to know why, so we can improve our service to you. Also this helps us able to keep giving you Great deals down the road as we strive for you to be a satisfied customer. If for some reason there is a problem, then please let us know before you leave feedback. This way we can fix it and make it right for you! Also make sure your ordering the right part for your car as shipping charges are not refundable. If you are not sure if a item will fit your car email us or send us a message trough ebay and ask us. When asking us please give us all the information about your car, so we can answer your questions quickly. INSTALLATION INSTRUCTIONS FOR EMBLEMS: Front Access to the emblem. On most vehicles you can open the hood and access the back of the grille without removing anything. On some models you will have to take the plastic panel, which runs the width of the truck, off to allow access to the back of the grille. On these models the panel is held down with screws or plastic clips. The plastic clips have a center piece you “pop” up a ½” with a flat blade screwdriver and then remove the whole clip. There are usually about 8 clips. On a few other models you may have to remove the grille for easier installation. It is usually held in place by several screws. Old emblem removal The original emblem is held in a couple of different ways. Most of them have 2 push clips over 2 plastic studs that hold it too the grille. Some have a plastic tang on the stud that you have to push to release it. Once you determine which one you have, either remove the clips (this can be difficult using a flat blade screwdriver can help), or push the tangs and remove the old emblem. Installing the new emblem With the new emblem out of the package install the studs (provided) in the threaded holes on the back of the new emblem. DONOT OVERTIGHTEN THESE AS YOU CAN PULL THE THREADS FROM THE EMBLEM. Once you have the studs installed simply insert the emblem. (Make sure the top is up if it doesn’t fit quite right try flipping it over) When you have it set, install the flat washers and nuts (AGAIN DONOT OVERTIGHTEN) and re-install any plastics, or the grille if you removed it. Rear The rear emblems are held on with double sided tape. To ease removal you can heat them with a heat gun or a hairdryer. Always pay close attention to the paint so you don’t overheat it and bubble it up. The old emblem has 2 plastic alignment studs so you have to pull it straight off not up or down. If you choose to try and pry it off make sure you protect the paint and don’t pry too hard. Once the old emblem is removed make sure the surface is clean and free of any wax, old tape, or dirt. Peel the protective covering off the tape on the new emblem, and install it to the vehicle. Make sure it is level before you attach it. This listing only comes with these items listed below: Price is for only 1 emblem(Front or Rear) or 1 pack(Front & rear) HARDWARE TO INSTALL THE EMBLEM TO TO YOUR TRUCK.

Price: 159.99 USD

Location: Dublin, California

End Time: 2023-12-04T22:23:57.000Z

Shipping Cost: 0 USD